Plumbing Basics: Before Bathtub Installation
Plumbing Basics: Before Bathtub Installation
Blog Article
Right here in the next paragraph you might get lots of excellent information and facts in relation to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately challenging task. If the old bathtub is readily easily accessible, the project can relocate speedily; if you need to open up a wall to remove the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have qualified on your own for the work and also fit attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is better to take into consideration utilizing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and also don't need to transform the arrangement of your previous supply of water pipelines.
Your devices as well as product list ought to make up the following:
Preparing for the Setup
First of all, the supporting framework supplied with the bathroom needs to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the supply of water. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub until the spirit level reads level.
To install faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub as well as also examine the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has been utilized at the very least when as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in area between the tap and the sink. Secure the tap in position with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The previous kind ought to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in complications with wetness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our article about Installing A Bathtub. Thank you so much for taking time to browse our content. Enjoyed reading our entry? Please share it. Let others locate it. I treasure reading our article about Installing A Bathtub.
Immediate attention? Call. Report this page